> For the complete documentation index, see [llms.txt](https://commanderhelp.verifone.com/llms.txt). Markdown versions of documentation pages are available by appending `.md` to page URLs; this page is available as [Markdown](https://commanderhelp.verifone.com/customer-documentation/petro-and-c-store/pin-pads/implementation-guides/m400/evpay-configuration.md).

# EVPAY Configuration

After the Verifone M400 terminal is installed, it must be configured for use with the VIPER. Before beginning, obtain the following network settings from the network host:

* IP Address
* SSL
* Mask
* Gateway
* DNS

### Accessing Configuration

{% stepper %}
{% step %}

#### Access the Welcome Screen

If the screensaver is scrolling, tap the screen to access the Welcome Screen.

<figure><img src="/files/Igm8vFgFawIo6FxoxSwS" alt=""><figcaption></figcaption></figure>
{% endstep %}

{% step %}

#### Open Configuration

At the Welcome Screen, press #,6,#,6 quickly. The Enter Configuration Password screen appears.

<figure><img src="/files/5uTB1yaJ6H3dXHmWuMx2" alt=""><figcaption></figcaption></figure>
{% endstep %}

{% step %}

#### Enter the password

Key in the password (**69900**) by pressing the number keys on the keypad.
{% endstep %}

{% step %}

#### Confirm the password

Tap the green check box or press the green circle button on the keypad. The main Configuration screen appears.

<figure><img src="/files/SF2nZ9wkcVlBsFibsypX" alt=""><figcaption></figcaption></figure>
{% endstep %}
{% endstepper %}

### Network Settings

Use the Configuration screen to access the Network Settings.

{% stepper %}
{% step %}

#### Access Configuration

Access the Configuration screen and enter the password. See “Accessing Configuration” for information about locating the screen.

<figure><img src="/files/VSETIyYlnQv1PmulBKY7" alt=""><figcaption></figcaption></figure>
{% endstep %}

{% step %}

#### Open Network Settings

Tap Network Settings. The Network Settings screen appears.

<figure><img src="/files/tu7MXN3eXLb7hliCI3bs" alt=""><figcaption></figcaption></figure>
{% endstep %}

{% step %}

#### Enter network values

Tap the screen to enter the values using the keypad.

<table><thead><tr><th width="143">Settings</th><th>Action</th></tr></thead><tbody><tr><td>IP Address</td><td>Key in the IP Address.</td></tr><tr><td>SSL</td><td>Tap to enable or disable SSL.</td></tr><tr><td>Netmask</td><td>Key in the Subnet Mask.</td></tr><tr><td>Gateway</td><td>Key in the Gateway.</td></tr><tr><td>DNS1/DNS2</td><td>Key in the DNS addresses should be obtained from the Site Network Administrator. Alternatively, the following public DNS addresses can be used:– 8.8.4.4– 8.8.8.8</td></tr></tbody></table>
{% endstep %}

{% step %}

#### Save or discard changes

Tap Apply or press the green circle button on the keypad to save the settings.

Tap Cancel to discard the changes and exit Network Settings to the Configuration menu.
{% endstep %}
{% endstepper %}

### Downloads

Use the Configuration screen to access the Downloads.

{% stepper %}
{% step %}

#### Access Configuration

Access the Configuration screen and enter the password. See “Accessing Configuration” for information about locating the screen.

<figure><img src="/files/eb1kCL1wPaQhoawvCNol" alt=""><figcaption></figcaption></figure>
{% endstep %}

{% step %}

#### Open Downloads

Tap Downloads. The Downloads screen appears.

<figure><img src="/files/HFPCyQlSeqJSdQfFlsF8" alt=""><figcaption></figcaption></figure>
{% endstep %}

{% step %}

#### Download a file

Tap the file to download and follow the prompting.
{% endstep %}

{% step %}

#### Exit Downloads

Tap BACK to exit Downloads to the Configuration menu.
{% endstep %}
{% endstepper %}

### EMV Information

Use the Configuration screen to access the EMV Information.

{% stepper %}
{% step %}

#### Access Configuration

Access the Configuration screen and enter the password. See “Accessing Configuration” for information about locating the screen.
{% endstep %}

{% step %}

#### Open EMV Information

<figure><img src="/files/jWtyp2GYfQqhGWSkYRmw" alt=""><figcaption></figcaption></figure>

Tap EMV Information. The EMV Information screen appears.

<figure><img src="/files/TS4F7rb88voLXYBk5GvK" alt=""><figcaption></figcaption></figure>
{% endstep %}

{% step %}

#### Exit EMV Information

Tap BACK to exit EMV Information to the Configuration menu.
{% endstep %}
{% endstepper %}

### RFID Support

Use the Configuration screen to access the RFID Support.

{% stepper %}
{% step %}

#### Access Configuration

Access the Configuration screen and enter the password. See “Accessing Configuration” for information about locating the screen.

<figure><img src="/files/O3oeyXJgwk97GSkAwYIG" alt=""><figcaption></figcaption></figure>
{% endstep %}

{% step %}

#### Open RFID Support

Tap RFID Support. The RFID Support screen appears.

<figure><img src="/files/lLVOOkiDsYzYLIrDKWsl" alt=""><figcaption></figcaption></figure>
{% endstep %}

{% step %}

#### Disable RFID

Tap the check box to disable RFID. RFID is enabled by default.
{% endstep %}

{% step %}

#### Save or discard changes

Tap Apply to save the settings.

Tap Cancel to discard the changes and exit RFID Support to the Configuration menu.
{% endstep %}
{% endstepper %}

### VHQ Configuration

Use the Configuration screen to access VHQ Con.

{% stepper %}
{% step %}

#### Access Configuration

Access the Configuration screen and enter the password. See “Accessing Configuration” for information about locating the screen.

<figure><img src="/files/HMc7VerYwp8vuI13U7qF" alt=""><figcaption></figcaption></figure>
{% endstep %}

{% step %}

#### Open VHQ Configuration

Tap VHQ Configuration. The VHQ Configuration screen appears.

<figure><img src="/files/ZfILUyHj4TF69PSRwLYh" alt=""><figcaption></figcaption></figure>
{% endstep %}

{% step %}

#### Configure VHQ values

* **VHQ Agent Version** — Displays the current Agent version.
* **Store ID** — Select to manually configure the Store ID up to 40-digits. The value will be displayed below at VHQ Store ID. If not selected, the EPS sends the value or the value displays zero.
* **Lane ID** — Select to manually configure the Lane ID up to 3-digits from 1-128. The value will be displayed below at VHQ Lane ID. If not selected, the EPS sends the value or the value displays zero.
* **Service ID** — Select to manually configure the VHQ Service ID. The value will be displayed below at VHQ Service ID. If not selected, the value displays zero.
  {% endstep %}

{% step %}

#### Save or cancel

Tap Apply.

Tap Cancel to return to the Configuration screen.
{% endstep %}
{% endstepper %}


---

# Agent Instructions
This documentation is published with GitBook. GitBook is the documentation platform designed so that both humans and AI agents can read, navigate, and reason over technical content effectively. Learn more at gitbook.com.

## Querying This Documentation
If you need additional information that is not directly available in this page, you can query the documentation dynamically by asking a question.

Perform an HTTP GET request on the current page URL with the `ask` query parameter, and the optional `goal` query parameter:

```
GET https://commanderhelp.verifone.com/customer-documentation/petro-and-c-store/pin-pads/implementation-guides/m400/evpay-configuration.md?ask=<question>&goal=<endgoal>
```

`ask` is the immediate question: it should be specific, self-contained, and written in natural language.
`goal` is optional and describes the broader end goal you are ultimately trying to accomplish on behalf of the user. GitBook uses it to tailor the answer towards what is most useful for that goal.

The response will contain a direct answer to the question and relevant excerpts and sources from the documentation.

Use this mechanism when the answer is not explicitly present in the current page, you need clarification or additional context, or you want to retrieve related documentation sections.