Earnify Configurations for Verifone POS or NCR POS

Configurations for setting up Earnify at site with Verifone POS or NCR POS with Commander setup.

Set up Earnify on Verifone POS or NCR POS sites running Commander.

Applies only to VeriFone POS or NCR POS sites with Commander. Do not use these steps for Gilbarco sites.

For Gilbarco sites, use Earnify Configuration for Gilbarco.

Before you start (inputs you need)

• Merchant ID: site-specific 6-digit Buypass MID (assigned by Fiserv / Payment Host).

• Site SVB: site-specific 7-digit SVB (used to build the Store ID).

• Site Address: copy from the top of a site receipt.

• Config Client access: Manager (or higher).

If you do not know the Buypass MID, contact the BP HelpDesk to retrieve it.

1) Log into Commander Config Client

Verifone POS

1. Select CSR Function (bottom-right).

2. Select Configuration Manager.

3. Sign in to Config Client with Manager user credentials.

NCR POS

2) Mobile Payment Configuration

1. Go to Payment Controller → Mobile Payment Configuration.

1. Open the Site Mobile Configuration tab and set the below fields:

• Accept Mobile Payments: Enabled (checked)

• Site Configuration

  • Site Name: BP MOBILE

  • Welcome Message: Welcome to BP Mobile

• Miscellaneous Configuration

  • Data Storage Time (In Secs): 30

  • Site Address: (site address from top of receipt)

1. Select Save button at the top right side of the screen. To save the configuration, Message box will appear to enter OTP, follow the step below to generate the OTP.

OTP generation steps (for OTP Prompt shown when saving some changes)

If an OTP prompt appears when you select Save:

1. Select Generate OTP.

2. Read the 4-digit code from the Commander device display.

3. Enter it into One-Time Password.

4. Select OK.

3) Mobile Host Configuration

1. In Payment Controller → Mobile Payment Configuration, open the Host Configuration tab.

2. Select Add.

3. Enable Host (check the enable box).

4. Under Host Configuration, enter this field first:

   • Site Terminal ID: Enter 002

Enter Site Terminal ID first. Then enter the remaining values.

1. Complete the remaining fields:

   • Adapter: Select VFI Mobile v1 from dropdown

   • Program Name: BP MOBILE (all caps/capital letters)

   • Merchant ID: <6-digit Buypass MID>

     • Note: Site-specific value, assigned by Fiserv (Payment Host).

     • If unknown, contact BP HelpDesk to retrieve.

   • Authentication type: Scan Token

   • Store ID: bppap + <7-digit Site SVB>

     • Example: bppap1234567

     • Note: bppap must be in lower case & no space before SVB

2. Leave these fields blank:

   • Settlement Employee number

   • Settlement Passcode

   • Phone number

   • Send Loyalty Details

3. Under Network Configuration, complete the following:

   • Address (Ipv4 Format/Domain Name): vfn6.na-rscs.bpglobal.com

     • If needed, you can use vfn1 , vfn2 , vfn3 vfn4 vfn5 instead of vfn6.

   • Port: 8499

   • TLS Enabled: Checked

   • Heartbeat Frequency: 45 or 90

   • Heartbeat Time Unit: Seconds

4. Under Misc Configurations, complete the following:

   • Outdoor Pre-authorization Timeout (In Secs): 90

   • Site Initiated Loyalty: Allow Site Entry i.e., Swipe Loyalty Card

5. Select Save (OTP maybe required. OTP can be generated by following OTP generation steps give above).

4) Mobile MOP Configuration

1. Go to Store Operations → Payment.

1. In Payment Manager, open the MOP tab.

1. Confirm a MOBILE MOP is setup.

1. Confirm the MOP code is set to:

   • 28 - MOBILE

1. Confirm the additional options match the picture below.

5) Car wash product + department setup

If the site has Car wash available, confirm Product and Department codes are set up correctly.

1. Go to Store Operations → Merchandise → Product Codes.

2. Confirm Car wash uses Product code 0102

1. Go to Store Operations → Merchandise → Departments.

2. Confirm the department is associated with Product code 0102

---

6) POS loyalty configuration

1. Go to Payment Controller → POS Configuration.

1. Open the POS tab. Complete the following configuration:

2. Under Batch, complete the following:

   • Batch Close Period: Day

3. Under Loyalty, complete the following:

   • Loyalty Enabled - must be checked

   • Multiple Loyalty Discounts in same Transaction - must be checked

   • Auth on Total - must be checked

   • EPS PPG precedes POS PPG - must be checked

4. Select Save button (OTP may be required. OTP can be generated by following OTP generation steps give above).

7) EPS Global Configuration

1. Go to Payment Controller → EPS Configuration → EPS Global Configuration.

1. Open the Loyalty tab.

2. Under Loyalty Configuration Parameters, enable:

   • Enable Alternate ID - must be checked

   • Display Host Messages - must be checked

3. Select Save (OTP may be required. OTP can be generated by following OTP generation steps given above).

8) Loyalty Card Configuration (only if local loyalty is present)

If the site has another PCATS (Local Loyalty) configured in Commander, following steps must be completed to add the Earnify FEP.

1. Go to Payment Controller → EPS Configuration → Loyalty Card Configuration.

1. Open the Loyalty Card Configuration tab.

2. Under Supported FEPs, select Add.

3. Enter VCMG in the box.

4. Select Save (OTP may be required. OTP can be generated by following OTP generation steps give above).

9) Disable swipe-ahead (Commander Base 55)

On Commander Base 55 sites:

1. Go to CSR Function → Maintenance → Device Configuration → PINPAD Configuration.

2. Select EPS PINPAD – With swipe-ahead disabled.

10) Datalogic scanner setup (VeriFone POS only)

This does not apply to NCR POS.

1. Go to CSR Function → Maintenance → Device Config → Scanner Config.

2. Set Installed Scanner to 2D Scanner – Com8.

3. Reboot the POS (required).

11) Test barcode scan

Scan the barcode below. Then test with an Earnify app barcode after reward is claimed.

Technical Support

For additional technical support, issues or any queries related to Earnify, contact [phone], Option 3, 1.